Can I Install A Bathtub Myself?
Can I Install A Bathtub Myself?
Blog Article
Presented here down the page you can get more sound expertise in regards to A Step-by-Step Guide to Installing a Bathtub.
Installing a tub isn't specifically rocket science, yet it does require strong plumbing, woodworking, as well as occasionally, tiling skills. Changing an old bath tub with a new one is additionally a moderately tough task. If the old tub is easily accessible, the job can relocate speedily; if you have to open up a wall to eliminate the old bathtub and position the brand-new bath tub, the job is much harder. In either situation, the job is within a residence handyman's skills, although you will certainly require a helper to move out the old bathtub and also set in the new one. Make certain you have actually qualified yourself for the task and also are comfortable attempting it. Instead of working with a contractor to take over a halfway-completed job, it is far better to take into consideration employing one before you begin. Possibilities are you might require a professional plumber to make tube connections.
This short article will certainly aid you mount a new bathtub in your restroom if you have actually currently acquired a brand-new tub and don't need to alter the plan of your previous water pipelines.
Your devices and material checklist ought to make up the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you should do is disconnect the water supply. After doing so, turn on the taps to drain any water remaining in the system. The process of removing the existing taps can be quite problematic due to the restricted access that is often the case.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a cloth ready for the remaining water that will certainly originate from the pipelines. When the supply pipes have been removed, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from transforming during this process. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleansed of any kind of old securing compound.
Before going on to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin making certain that the washers are in area between the faucet as well as the sink. Secure the faucet in place with the supplier supplied backnut. Once the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet ports. The former kind should be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Bath tub
Using both wooden boards under its feet, put the bathtub in the needed position. The wood boards are helpful in uniformly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four little factors.
The next objective is to ensure that the tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the bathtub up until the level reads degree.
To mount taps, fit all-time low of the outermost flexible faucet adapter to the suitable supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water and inspect all joints and also new pipework for leaks and also tighten them if necessary. Fill up the tub as well as also inspect the overflow electrical outlet and the normal electrical outlet for leakages.
Finally, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bath tub should wait up until the tub has actually been made use of at least once as this will resolve it right into its last position.
Preparing for the Installation
First of all, the sustaining structure provided with the bath should be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to make sure that if the tap includes a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop strain on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet through the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you use all of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom must now be ready to be suited its last setting.
Tiling Around the Bathtub
In the area where the bathroom fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a stiff seal, causing the water to pass through the wall surface between the bath and also the tiling, causing problems with dampness and also possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes and also cartridges, as well as are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always fill up the bathtub with water prior to sealing, to permit the motion experienced when the tub remains in use. The sealer can break rather very early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily offered on the market. It is a good idea to fit the tiles making use of water-resistant or water-proof adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was shown that editorial about How to Install a Bathtub through someone on our other website. Do you know somebody else who is fascinated by the niche? Feel free to promote it. We treasure reading our article about How to Install a Bathtub Yourself.
Schedule Today!
Report this page